17 Best Table Saw Stand With Wheel (2023 Updated)

I love this little stand. I don’t use a table saw a bunch. I am a track saw and for any cut longer than 10″ I am using a track saw. So for me, being able to tuck my saw away on a shelf is more important than anything else.

I used to use a folding table for my table saw, but it sat the saw higher than ideal. This stand puts the saw pretty low and I am not that tall (5’10”), but the small size for storage or transport just can’t be beat.

This stand is stable and holds the saw well and when I am not using it, I can hide this tiny stand anywhere. I use a couple of clevis pins to hold the saw onto the stand so that I can easily take it on and off, Many people would probably use it without anything holding the saw on, but I like the extra safety of the pins.

I use it for sight work, the only thing it’s missing is a quick connect to hold the saw in place. Bolting, and unbolting is not quick. Also a leveling foot would be nice!

This is so stupid. It’s like a 1 foot stand. So you put it on the stand, and then you would have to put the stand on a table otherwise i hope you like doing it from your knees.

I put together my new shopfox and it is nice and sturdy it holds the weight of my plainer fine. Just one of the swivel wheels was a little screwed up. Some how before I installed it. ! It looks like ine of the ball bearings was crushed inside not very smooth and squeak’s even after oiling it.

But all in all it is a good product. Just my luck I get the bad caster! Also I think they would be easier to move if you had swivel casters on all 4.

Very sturdy. Much lower than other mobility kits. Used this for a 12” jointer planer that weighs about 500 lbs. it’s very stable and maneuvers easily in my basement shop.

Easy to use, producing a really nice marmalade. Used several times!

I just purchased the DWE2485 table saw and the DW7440RS stand. After reading several reviews that said the mounting holes don’t match, I must say they were wrong. The mounting holes match perfectly if you do it correctly.

Some talked about the holes in the saw being angled, these are the wrong holes to attach to the stand. The holes under the rubber feet are the ones to use. Thank you DeWalt for an easy and quick setup.

I have owned this stand for my Dewalt table saw for about 3 years. It stays in my truck full time. I absolutely love how portable it is and how quickly it sets up and breaks down. I can remove the saw and carry the stand and saw separately or roll them both together.

I have owned other jobsite table saws but they always had issues with long rips or with heavy plywood. This combination of a wide stance and easy setup makes it amazingly stable and increases the accuracy of the cuts.

I own many Dewalt tools, this is by far my favorite.

Comes mostly assembled. You just add the wheels and kickstand. I wasn’t sure about the bolts and nuts but I looked at a video on YouTube and it went together perfectly. Comes with the hardware to mount your saw and it’s very sturdy.

I don’t know why I waited so long to mount my saw. Cutting anything on the ground will surely make you sore after getting up and down a lot. This stand solves that because it’s all together in one place.

The legs fold out and lock securely and easily fold back in when you’re done. No more setting up saw horses! If you did need the saw without the stand, it can detach from the stand and still sets on rubber cushions just like the saw did when you first bought it.

Then it connects back to the stand with ease. Search YouTube with the model number of this stand and you’ll see how awesome it is.

We bought our Dewalt 7491 Job site table saw 3/19/2019. It was awesome until I changed the blade out from the original Dewalt blade to Diablo blade. We have always used Diablo blades in our table saws.

This is not our first table saw but it is our first Dewalt table saw. Most of our tools are Dewalt, so we thought we would go with the Dewalt table saw. Very disappointed after changing out the blade after two years of use, it was pretty dull as you can imagine.

No matter what I do, the arbor nut keeps coming loose after about 4-6 cuts. I have made sure I have the nut on correctly, first thing I checked. I’m going to call Dewalt to see if I have options. We love Dewalt tools.

Very solid and pretty easy to assembly There are a couple of different DeWalt saws with different hole configs. The stand came with an adapter piece so I could securely attach my saw to the base. So far so good.

I bought this with my table saw about a month ago and it’s been holding up to the abuse I’ve given it in my shop. It compacts well and carries the table saw just fine when I need to move it. My only drawback is the overall size when set up.

This is a great option for setting up a work station at a job site but it’s not what I would recommend if you are setting it up in a small to medium shop. My shop is 16×20’ and it commands a lot of the shop floor.

But overall it was designed for the job site and it does work well in this setting.

This stand is very well designed and good quality. Easy to use and stable platform for cutting. Stable when standing upright in storage mode (with legs folded) too. Makes moving the saw much easier than carrying it (but do wish it had some type of roller strap on the back to make it easier to load into a vehicle single handed).

The stand saw attachment slides adjusted easily for the install of a Hercules saw, and given the amount of adjustment it affords (in two axis) would probably accommodate any portable saw on the market.

First, this stand is rock solid even in the dirt. The wheels are big enough to roll through and over clumps of dirt around a construction site. The legs snap into either the locked position for travel & storage or for work and dont budge.

When this stand is in the storage and travel position it is tiny. It tskes up less space in the vertical position than it does sitting on the DeWalt stand it came with, on the shop floor or in the bed of your truck depending on where you store it and I think it makes using the table saw more convenient.

Have you evef had a rip that should be made using a table saw, but for the hassle of digging it out from wherever it’s stuffed into, finding the stand to get it off the floor and over everything in the way you just say, “the heck with it,” and use your circular saw.

I struggled with the purchase, but this thing is worth it in my opinion.

Stand is very sturdy and works great. I purchased the stand to custom mount a router table for portability. Would send picture but it has a different brand router table mounted on the Dewalt stand.

Finally I can rip boards standing up! Extremely stable and heavy duty design, perfect working height, safe transport. Assembly was as directed in manual. High quality parts and instruction. A wheeled cart design is so welcome.

I’m 60 and this will help greatly. Well done.

Does the job but needs to have a lock to keep it closed extremely hard to get through a standard door and the fact it keeps springing open doesn’t help! Altogether good but a few design flaws

It is a good trolley with simple assembly. The unlocking up and down mechanism is clunky, you need to squeeze it hard to make it work once loaded with the saw.

Great product. Very pleased with purchase. Would definitely recommend.

In order to keep saws in this category small and light weight some compromises must be made. Some parts are not as strong and beefy as one would like for accurate cutting. This saw is as good as any in most respects and better than some in other areas.

It is light but sturdy but the biggest advantage is the worm drive. Most portable table saws are direct drive which are loud and run at an obscenely high blade speed. The Skilsaw runs at a slower speed and has a lot of torque.

It is also quieter. All in all, I am happy with my purchase.

Adapted to use with Dewalt DWE7480 table saw by making a plywood base with 4 feet to fit exactly into the recessed places for the intended Skilsaws feet. Added four toggle clamps from amazon to clamp saw to base.

Now I have a multi use stand that I can break down and put away or set up in seconds. Love it!.

Definitely better table saw stand than any other table saw I have. However, I don’t know or haven’t decided if I will keep it and may upgrade to a heavier duty movable table saw stand. I would definitely buy this stand again though, it really is pretty good.

The photos online make it look almost whimpy, but in real live it is decently stout for what it is.

Bought this 3 weeks ago. Fits the Bosch GTS saw perfectly. I am 6 ft tall and is a good height for me. Wish my work bench was this height! I have it on my garage floor which isn’t particularly level and it doesn’t wobble at all.

Very impressed with this. No defects in the paint seen/found either. I price is a little on the steep side from other suppliers. Good price from Axminster though.

This is a good strong, heavy stand. Well finished in Bosch red with rounded plastic feet and handles either side to release the legs and fold flat. It’s weight is both it’s strength and it’s downside as it’s heavy to lug around and the weight makes it relatively difficult to extend and to collapse.

The meachanism is quite straightforward but demands a clean pull on the two handles (in the middle of each of the left and right sides) both at the same time. I bought this to use as a collapsible low table, adding my own top.

Even without the weight of a saw fitted it cries out for wheels !.

I saved over 70 on this item. Its perfect for my saw the Bosch GTS 10 XC. Its very sturdy and is very easy to put away. I find its a little to high for me but thats it. Thank you. Every blessing in Christ.

I purchased this stand to fit the GTS 10 J table saw. Easy to assembly only four M8 bolts to secure the leg extensions in place. Once the stand is opened up there are two hinged brackets which locate the table saw and an additional spring clip to hold everything together.

The stand and saw fit together perfectly and it’s really stable. Lifting the saw into place is rather trick due to its weight, the same with taking it off, this is no criticism of the stand. The same clip to hold the saw in place is used to lock the stand when folded.

If you can’t stretch to the folding stand with wheels buy this!.

Superb stand. Forget trying to mount your table saw on a bench, workmate or some other alternative table and just get one of these. Light weight but sturdy and not outrageuosly expensive. Recommended

I should have bought this with the table saw. Great add on and very stable. Only design flaw is the bits that the saw glide into,it’s on hinges and is a bit in the way when folding it up but not a major issue.

Good solid stand for DWE7485-GB which arrived incredibly quickly given just before Xmas. Design would be better if there was a quicker fixing method to secure saw to stand.

This stand was on offer when I bought my table saw. It is very rigid and can clamp DW745 using spring clamps and a clever design. I also used the supplied bolts because my table saw is permanently in my garage.

There is a more expensive folding stand but I would be surprised if it was any more rigid – just the flexibility to collapse it.

Good study portable stand. The only bad thing is having to bolt the saw to it each time you set up but I bought some 6mm clevis pins to make set up quicker

I recently moved and had to leave my 30 something year old craftsman table saw behind knowing I would have to replace it. When I looked at all of the saws at Lowes one thing was very apparent-You can buy a cheap table saw and that’s what you’ll get.

I really didn’t want to spend as much as I did for this saw but when it went on sale I couldn’t resist. Anyway, assembly of the stand was really easy and straight forward. The saw bolted right on and the stand is a breeze to stand up and put out of the way.

The only adjustment I had to make was a very minor adjustment of the plastic scale for zero. All of the cuts I have made so far have been dead on. I didn’t have to make any adjustment for the fence, It works smoothly and was parallel to the blade.

It’s really neat the way that there is storage for all of the accessories to keep them out of the way. If I had to complain about anything it would be about the supplied wrenches. They are very thin and will deform if you tighten the nuts and bolts too tight.

All in all I think this is a quality product and well worth the cost especially when compared to cheaper saws.

I spent several weeks researching various modles of “Jobsite” or portable table saws: Skil, Metabo, Bosch, Sawstop, Rigid and of course DeWalt. I looked at many features: blade size, width of rip (able to rip a plywood sheet in half) , type/design of rip fence, stand design, set-up/alignment/adjustability for accuracy, motor power, etc.

I also read many, many customer reviews. One saw stood out for me, DeWalt DWE7491RS. It got high scores for every attribute that was important to me including a competitive price. I bought it yesterday and set it up today.

The quality of the build is excellent. All of the power train, controls and adjustments are metal. The alignment of all the critical components was near perfect right out of the box. I did find that there was shipping damage to the fence.

I called DeWalt customer service and a replacement fence is on its way at no charge. The table is flat, the blade is perpendicular to the table and the fence is parallel to the blade within 1/64 of an inch.

The blade comes to speed in a moment and does not dim the lights or pop the breaker. When folded up, it only takes about 4 square feet of floor space. It is relatively light weight and can be easily set-up/broken-down/moved around.

The legs are strong and steady given the angled attachment. I am happy with my choice, it is the right saw for me. I strongly recommend it to anyone who wants a high quality saw, moderate price, and compact size.

I am a professional contractor and this review is long overdue. The DeWalt DWE7491 10″ table saw is the best I have used in my 25+ years in the construction industry. It’s fence system is accurate and easy to use, it has plenty of power and is super easy to transport and store.

I use, and review a fair amount of tools and the DWE7491 10″ table saw is the first tool that I have not one negative thing to say about. I mean I usually have at least something a manufacturer could do better.

Not with this saw, it’s perfect out of the box. This is the second one I have purchased this year, I was so impressed with the one I purchased for my business, that I bought one for my personal use. I highly recommend this tool.

Great job DeWalt.

I kind of bought this on a whim. A saw it at the Plymouth Mn store and really didn’t give it much consideration. go home and did some research and discovered what it could be used for and how it would fit into my home shop and it’s usage.

Well, after a week of using it for some bedroom furniture projects I’m not sure I could live without it! From easily loading material from the back of my truck and rolling it into the back shop of my garage, to using it as a cutting station and sanding station.

It has been great. One of the best features though is I can store it when it’s not needed under my table saw extension table. Also under the extension table are 2 MFT/3’s on their sides. This setup can turn my 4 car garage into a 1000 square foot shop in about 10 minutes or back to parking 3 cars in about the same time! I’m new to Festool but not for long.

Great equipment and it works so well together.

Great for small space. Portable and sturdy. U can use an MFT top at and 4 sides coz it’s big. Easy to cut a 4×8 sheets of ply. I’m glad I got this table. Better get one before there out I heard this will be limited only.

The only thing I don’t like is the price. I guess price makes your life easier.

Although I haven’t used my 55 to Saw on It, it’s Been a Great work And assembly Table! And yes, it Stays in My small Shop! 16×24 it’s A small space. However, when I need to assemble my latest project, restoring an old cast iron garden bench, it worked perfectly.

When I’m working and need extra space, it worth ever penny!!.

Very happy with the purchase, best price around at the time of purchase, it was actually cheaper two months earlier but i never had the funds, good comms

This is so well made, and easy to use, assemble etc. The fact that it can be used anywhere , depending on widths is just great. It will definitely outlast my table saw. fingers crossed it wont. A little on the heavy side but hey hoh what in life is perfect.

Very heavy. Not great at getting the saw up steps as the wheels are not big enough or far enough out from the saw. Solid when using the saw so all in all it’s great when using it with table saw.